Epoxy Batch Size and Pot Life Calculator
Scale the pot life on your data sheet for the material temperature and see the largest batch your crew can use before it goes off, and how many batches to split a kit into.
How Much Epoxy to Mix at Once
A kit is a packaging decision, not a batch size. Enter the pot life from the data sheet and the temperature it is quoted at, the temperature of the material, how long mixing takes, the kit volume, and how fast your crew puts material down. The tool scales the pot life for the day and tells you the largest batch the crew can use before it goes off in the pail, and how many batches to split each kit into.
From the Data Sheet
The pot life and the temperature it is quoted at, plus the mixed volume of one kit.
On Site
The material and the crew on the day. Take the temperature of the material itself, not the room it came from.
Enter the pot life, its temperature, the kit volume, the material temperature, the crew pace and the coverage to see the batch plan.
Pot life is scaled from the values you enter by the standard rule that reaction speed roughly doubles for every 10°C (18°F) of warmth, the same model as the recoat window calculator. Two things it does not model: a sheet measures pot life on a stated mass, and a deeper batch in the pail holds its heat and goes off sooner; and it plans as if the batch is worked out of the pail at crew pace, so pouring it straight out onto the floor changes the limit. Split a kit with the mixing ratio calculator. The data sheet wins wherever it gives a figure or a limit.
How the Epoxy Batch Size and Pot Life Calculator Works
- Enter the pot life from the data sheet, in minutes, and the temperature the sheet quotes it at
- Enter the mixed volume of one kit (Part A and Part B together)
- Enter the temperature of the material itself, not the room
- Optionally add how long mixing takes, from combining the parts to material going down
- Enter the crew pace in floor per hour and the coverage at this coat
Examples
Frequently Asked Questions
How much epoxy should I mix at once?
The largest amount your crew can get onto the floor and spread before its pot life runs out, under the conditions you have that day. That depends on three things: how long the material stays usable at its temperature, how long mixing takes out of that time, and how fast the crew puts material down. Kit size is not one of them. If a full kit is more than the crew can use in time, mix part of it.
Why does temperature change the batch size so much?
Because the reaction that cures the material speeds up as it warms. The working rule, and the one this tool uses, is that it roughly doubles for every 10°C (18°F). Material one step warmer than the sheet's reference temperature has about half the printed pot life, so the crew can only use about half as much before it goes off. On a hot day the answer is less material per mix, not working faster.
Which temperature should I enter?
The temperature of the material itself. Pot life is about the mixed product in the pail, and a kit that sat in a hot truck or a cold trailer is not at the temperature of the building it is being used in. Check the material, not the air. The slab matters for how the coat cures once it is down, which is a separate question.
Is it safe to split a kit?
Usually, provided you split it by the ratio rather than by eye, and the mixing ratio calculator sizes a part batch without breaking it. Some products should not be split, typically small pre-measured units and some fast systems, and the data sheet will say so. Where it does, that instruction overrides this tool.
Is pot life the same as gel time or working time on the floor?
No. Pot life is how long the mixed material stays usable in its container. Gel time is a laboratory measurement of when it stops flowing, and by then your usable time is long gone. Working time on the floor is often longer than pot life, because a thin film loses its heat to the slab while a mass in a pail keeps it. This tool plans around pot life, as if the batch is worked out of the pail at crew pace.
Why is nothing pre-filled?
Because pot life belongs to your product, and it differs widely between chemistries and between fast and slow versions of the same product. This site does not publish generic pot life figures. The examples on this page use an illustration data sheet, labeled that way, to show how far temperature moves a batch.
Important Notes
- Nothing is seeded. Pot life and its reference temperature come off your data sheet.
- The scaling is the standard rule that reaction speed roughly doubles for every 10°C (18°F), the same model the recoat window and cure time calculators use.
- A data sheet measures pot life on a stated mass of material. A deeper batch in the pail holds its own heat and goes off sooner than the tool shows, so treat the largest batch as a ceiling.
- The tool plans as if the batch is worked out of the pail or tray at crew pace. Pouring a batch straight out onto the floor lets heat escape, and the sheet's working time on the floor is the limit then.
- When the material is more than 10°C (18°F) from the sheet's temperature the tool flags it. That limit is our caution, not a published standard.
- Where the data sheet gives a batch limit, a pot life for your temperature, or says not to split a kit, the data sheet wins.

