Pot Life

How long a mixed coating stays usable in its container. The clock starts the moment the two parts meet, it runs faster in warmth and in a full pail, and it ends well before the material stops being liquid.

What pot life means

Once the two parts of a coating are mixed, they start reacting, and nothing on site stops it. Pot life is the time the mixed material stays usable in its container: thin enough to pour, spread and level into the film the system was designed for.

The word that matters is usable. The material does not have to have set for its pot life to be over. It only has to have thickened enough that it no longer goes down properly. That point comes well before the material stops being liquid, which is a separate figure called gel time.

The clock starts when the parts meet

Pot life runs from the moment Part A and Part B come together. Everything after that comes out of the same budget: mixing, scraping the sides, transferring to a clean pail, carrying it to the work area and getting the first of it onto the floor. A batch that takes a long time to get going has already spent part of its life by the time anyone picks up a roller.

Why the pail is where it runs out

The reaction gives off heat, and heat speeds the reaction up. In a full pail that heat has nowhere to go, so the material warms itself and its pot life shortens. Spread thin across a slab, the same material loses its heat and stays workable for longer. Exotherm covers why the shape of the material matters more than how much of it there is.

Temperature works the same way from outside. Warm material, a warm room or a kit that sat in a hot truck all shorten pot life, and cold lengthens it. That is the reason a data sheet always quotes the figure at a stated temperature, and the data sheet guide covers the conditions every timing figure on it assumes.

What the end looks like

The signs arrive together and quickly. The pail warms and then gets hot to the touch. The material thickens, rolls heavier, strings off the roller or squeegee, and stops flowing out behind it. Material laid in those last minutes goes down too thick and does not level, and that part of the floor is what you will be looking at afterward.

So the end of pot life is not a signal to work faster. It is a point to have finished before. Material that has reached it goes in the waste pail. Thinning it to get a little more out of it does not slow the reaction, it only changes what ends up in the film, so do not add anything the data sheet does not call for.

Planning around it

The figure on the sheet is a starting point rather than a promise: it describes one test on one amount of material at one temperature. The practical question is how much to mix at once so that every batch is on the floor and spread before its pot life runs out. How to mix epoxy properly covers that judgement, and the batch size calculator turns your sheet figure, the material temperature and your crew's pace into a batch size.

Frequently Asked Questions

When does pot life start?

The moment Part A and Part B meet. Not when mixing finishes, and not when the first material reaches the floor. Mixing, scraping the sides, boxing into a second pail and carrying it to the work area all come out of the same budget.

That is why a slow start to a batch costs more than it seems to: the minutes spent getting organized are minutes the crew no longer has on the floor.

How do I tell a batch is reaching the end of its pot life?

The pail gets warm, then noticeably hot. The material thickens, rolls heavier than it did at the start, strings off the roller or squeegee and stops leveling behind it. Those signs arrive together and they arrive quickly once they start.

By the time you notice them, the material going down is already thicker than the film the system was designed for. Plan to finish a batch before the signs appear rather than using them as the signal to stop.

Can I thin a batch to get more time out of it?

Not unless the data sheet says you can, and with what. Adding solvent or anything else to a batch that is going off does not slow the reaction down. It changes what ends up on the floor: a thinner film, different solids, and a coating that may not cure or bond the way the sheet describes.

Material past its pot life belongs in the waste pail, not on the floor.

Why do I get less time than the data sheet says?

Because the printed figure describes one test, at one temperature, on one amount of material. A warmer day, warm material, or a fuller pail than the sheet tested all shorten it, and on a jobsite at least one of those is usually true.

The batch size calculator adjusts the sheet figure for the temperature of the material and sizes a batch your crew can use inside it. It cannot account for a bigger mass in the pail, so treat its answer as a ceiling.

Is pot life the same as working time on the floor?

No. Pot life is about material in its container. Once a coating is spread thin across a slab, its heat can escape, and it usually stays workable for longer than it would have in the pail. That is why many crews get a batch out of the pail and onto the floor quickly.

Some data sheets give the two separately. Where yours does, plan the pail around pot life and the floor around working time.